[Överensstämmelse]
· Styrets diameter: Φ22.2
Grepp ytterdiameter: Φ33
· Griplängd: 115/120 / 130mm
・ Exklusiv produkt för 12V fordon
[Inkluderade delar:] Värmekrymprör för greppskydd
* Liten handtagdiameter (Φ22.2 eller mindre) Fordon och tumstänger (Φ25.4) , Batterikapacitet · Kan inte användas för fordon med låg energiproduktion. (Start kräver 12,5 V spänning)
* För att fästa den medföljande förlängningshylsan, applicera lim på det område där förlängningshylsan ska monteras med greppet och kläm fast den ordentligt. Om en extrem belastning appliceras på förlängningshylsan kan förlängningshylsan falla av eller greppet avsluta och förlänga Observera att detta kommer att orsaka skador på hylsan.
* Eftersom värme sprids av handtaget, stångänden, handsken och kylning av löpande vind kan känslighetstemperaturen kännas låg.
* Använd en värmepistol för att fästa det medföljande värmekrympbara röret för greppskydd, och när greppvärmaren är uppvärmd kan det anslutna skyddsröret bli mjukt och lossna på grund av värme, så installera det när värmaren inte används. Det är rekommenderat.
* Om röret lossnar efter installationen, krympa värmen igen med en värmepistol för att få den i nära kontakt med greppet.
* På grund av skyddsrörets egenskaper har den totala längden en tolerans på cirka plus eller minus 3 mm, och ändytan kan vara något lutande, men det är inte en defekt produkt.
* Den inre diametern på höger grepp är .425,4. Om det är litet eller löst, använd den bifogade aluminiumtätningen och justera spalten med greppet.
* Det kanske inte är tillgängligt för SUZUKI-bilar med låg batterikapacitet och kraftproduktion och HONDA-bilar med batterier mindre än 7S.
* YAMAHA-fordon kan användas med 4B5 eller högre batteridrivna fordon.
[Compatibility]
・Handle Diameter: Φ22.2
・Grip outer diameter: Φ33
・Compatible grip length: 115 / 120 / 130mm
・Exclusive for 12V vehicles
[Components] Heat-shrinkable tube for grip protection
*Not for use with vehicles with small handlebars (Φless than 22.2), inch bars (Φ25.4), or vehicles with low battery capacity or power generation.(A voltage of 12.5V is required for start-up)
*When installing the supplied extension sleeve, apply adhesive to the inside of the extension sleeve where it meets the grip, and crimp it firmly.Please note that extreme load on the extending sleeve may lead to the falling off of the extending sleeve or the breakage of the grip end and the extending sleeve.
*Please understand in advance that you may feel lower temperature due to the heat radiation to the handlebars, bar ends and gloves, and cooling by the driving wind.
*Use a heat gun to install the heat shrink tubing for grip protection provided.Also, when the grip heater is heated, the protective tube may soften and loosen due to the heat, so it is recommended to install it when the heater is not in use.
*If the tube becomes loose after installation, heat shrink it again with a heat gun to make it tighter to the grip.If it still does not adhere, please remove the product as it may be the end of its life.
*The total length of the protective tube has a tolerance of plus or minus 3mm due to its characteristics.The edge of the product may be slightly slanted, but this is not a defect.
*The inner diameter of the right grip is Φ25.4.If the throttle sleeve of the vehicle to be installed has ribs, cut them to a height not lower than the inner diameter of the grip before installation.If the outer diameter of the throttle sleeve is smaller than the inner diameter of the grip and the throttle sleeve is loose, use the supplied aluminum seal to adjust the gap between the throttle sleeve and the grip.
*This product may not be used for SUZUKI vehicles with low battery capacity and power generation, or HONDA vehicles with batteries less than 7S.
*Yamaha vehicles with 4B5 or higher batteries can be used.