Den är flexibel och tryckjusterbar.
Slipskiva för Guld-släkte för 100mm skivmaskin.
Används huvudsakligen för borttagning av svetspärlor, BALI-borttagning, rostborttagning och platt ytpolering.
[Funktion 1 · Flexibel och tryckjusterbar]
Slipduk står på baksidan och fäster vid den, vilket gör det möjligt att justera trycket och flexibiliteten till föremålet.
Och om det finns en bakre bas, kommer du att öka ytpoleringskraften genom att trycka på den.
Visar kraft i plan, böjd ytpolering och ytutjämning.
[Funktion 2 · Visa kraft mot vändning]
・ När du trycker på det blir trycket starkare när du träffar bassidan djupt.
・ Om du trycker helt på den kommer den att vara nära Flat eftersom böjningen försvinner.
Från denna punkt, om det finns ett utsprång på ytan, ger det ytbehandlingen kraft eftersom det prioriterar skärning.
(Såsom polering av svetspärla)
* Tillägg *
Eftersom vingarna bara faller i sidled är det särskilt användbart när du vill jämna ut det svetsade pärlan med avgassystem etc.
* Det finns lite grävning eftersom andra träffar än Bead är svaga och Minus-ansiktet är svårt att komma ut.
[Funktion 3 · Kompatibilitet med låg hastighetskvarn]
Du kan använda den med en normal kvarn, men den har också utmärkt kompatibilitet med den långsamma kvarnen.
[Funktion 4 · Om slipstenen Alumina]
Slipningsduk med slipande tyg är aluminiumoxid, för allmänt guld.
Poleringskraften är lägre än Zirconia, men ytan är Mild även vid samma antal.
[Om skivmaskinens rotationshastighet]
Låg hastighet (Låg hastighet) När den används i, blir centrifugalkraften liten, så kontakten mellan poleringsskivan och arbetsstycket blir mjuk.
I synnerhet är basens fasta påverkan liten. "Mjuk" "Luft" Formen på polerduken blir lätt att vara kompatibel med föremålet som ska poleras, och det blir lätt att utföra poleringsskärningen längs formen på den böjda ytan.
Dessutom är det möjligt att minska slitage, skador, bita och fånga på grund av spridningen av polerduken.
* Det faktum att det är lätt att hantera enhetligt vid efterbehandling leder också till att Scratch minskas.
Å andra sidan, vid kraftig skärning, blir skärhastigheten långsammare på grund av en svagare träff och en minskning av mängden arbete på grund av minskningen av rotationshastigheten.
"Flat" och särskilt "Cut" Vi rekommenderar att du använder en allmän höghastighetsrotationstyp.
[Slow Grinder]
* Det är vanligt att använda låg hastighets skivmaskin med högt vridmoment med hastighetsändringsfunktion och hastighetsregulator.
[Kompatibilitet med låg hastighet och hög hastighet]
Låg hastighet <---> hög hastighet
Mjuk / Luft / Flat / Cut
40/120/320
Flexible, pressure adjustable, good for beveling.
Abrasive discs for metal for 100mm disc grinders.
Mainly used for weld bead removal, deburring, rust removal and flat curved surface polishing.
[Feature 1 - Flexible and pressure adjustable]
The abrasive cloth is bonded to the backing base in an upright position and flexes to provide flexibility and pressure adjustment to the object.
The backing increases the flat grinding force when pressed.
It is effective for flat and curved surface polishing and facing.
[Feature 2 - Effective for grinding]
・As pressing it down, the deeper it hits the base side, the stronger the pressure becomes.
・As it is pressed completely, it becomes flat because it does not bend.
Therefore, if there is a protrusion on a flat surface, it is shaved in priority, and it is effective for surface preparation.
(Grinding of welded beads, etc.)
*Supplement*
Since the wings only fall to the side, it is very useful especially when you want to smooth the weld bead of the exhaust.
*Because of the weakness of the contact other than the bead, there is little digging and the negative side does not appear.
[Feature 3 - Compatibility with low-speed grinders]
It can be used with a standard grinder, but it also works well with a low speed grinder.
[Feature 4 - Grindstone Alumina]
The grinding wheel of the abrasive cloth is alumina for general metal use.
Polishing power is inferior to that of zirconia, but the finish is milder than that of zirconia.
[About the speed of the disc grinder]
When used at low speed (low rotation speed), the centrifugal force is reduced and the contact between the grinding disc and the workpiece becomes softer.
This makes the shape of the abrasive cloth more familiar to the workpiece, especially in the "soft" and "air" types where the fixing influence of the base is small, and makes it easier to perform abrasive cutting along the shape of curved surfaces.
In addition, the wear and tear, damage, biting and snagging caused by scattering of abrasive cloth can be reduced.
*It is also easy to operate evenly when finishing, leading to a reduction in scratches.
On the other hand, in heavy-duty cutting, the cutting speed becomes slower due to weaker contact and lower workload caused by reduced rotation speed.
For "Flat" and especially "Cut", recommending the use of a general high-speed rotation type.
[slow grinder]
*It is common to use a disc grinder with variable speed function, low speed and high torque type and speed controller.
[compatibility with low and high speeds]
Low speed <--------> High speed
Soft / Air / Flat / Cut
40 / 120 / 320