Full uppsättning med fastsättning / skruvar som behövs för installation.
Dessutom Antal: Säljförsäljning endast begränsad ersättning Bakre boxInner är bifogad.
■ Bakre bärare med 4 modeller som delas är klar.
Yamahas YZF-R25 och YZF-R3, MT-25 och MT-03 har en gemensam motor och ram. Karossens sammansättning är lite annorlunda men den kan justeras till 4 bilmodeller. Bakre bärare har utvecklats.
YZF-R25 som antar Cowling och Design som påminner om SUPER SPORTS 750 och MT-25 som följer Bild av STREETFIGHTER-serien Båda bilarna är Slim och Sharp Image and Motorcycle, vilket är lätt och kraftfullt prestanda attraktivt.
Bakre bärare är en praktisk del, men jag konstruerade den så mycket som möjligt för att inte förstöra Sharp Image.
■ Designad som skarp som möjligt samtidigt som passageraren rymmer.
Ursprungligen försökte jag bakre bärarens ram upp till SeatLimit för att inte förstöra den strama bilden med Sharp. Det var designat som jag menade, men när jag försökte sitta på passagerare blev jag trång.
Så vi designade den något bredare än den ursprungliga provvaran så att även en bra manlig sittande på passagerarsätet har råd, jag avslutade det som Tight utan att offra passagerarens komfort.
■ Maximal Stor lastkapacitet är 5 kg. Vi förstärker varje del.
Nyligen, även i fordon som bildas SUPER SPORTS 750 Bakre bärare och bakre låda Mängd: Det blir vanligt att installera med Set. Stor textur Bakre rutan har en vikt på ca 5 kg så vi förstärker varje del så att den maximala Stora lastkapaciteten är 5 kg.
Placera förstärkning Placera en förstärkning Platta i ramdelen där bakbäraren är monterad och förstärkning läggs också på fotdelen av kroppen.
■ Buckling form som betonar praktiska och design.
Baklucka Det finns möjlighet att locket stängs utan tillstånd om locket öppnas horisontellt eller locket öppnas uppåt vid öppning av bakre bärkroppen, så att bakbärarens kropp har en form som stiger bakåt. Det är ett design med enighet som passar vinkeln på Tail cowl.
Installation görs genom att ta bort Grab Bar från MT-25/03. Även om det är nödvändigt att borra en del av Tail cowl i YZF-R25 / 3, är den konstruerad så att borrningen av Cowl är den minsta gränsen. Vi har även ett pappersmönster så att borrningspositionen är lätt att förstå.
Full set with base and screws required for installation.
In addition, the set comes with a limited edition rear box inner.
■The rear carrier for the same four models is available.
Yamaha's YZF-R25 and YZF-R3, MT-25 and MT-03 each share the same engine and frame.Although the vehicle configuration is slightly different, World Walk has developed a rear carrier that can be adjusted to fit four different models.
The YZF-R25 has a cowling and design reminiscent of supersports, while the MT-25 follows the image of a street-fighter.Both bikes have a slim, sharp image and are lightweight with powerful performance.
The rear rack is a practical part, but World Walk designed it not to destroy the sharp image as much as possible.
■Designed to be as sharp as possible while retaining space for the passenger.
In order to keep the sharp and tight image of the bike, the frame of the rear rack was brought up to the very edge of the seat.The design of the vehicle is as World Walk wanted, but it is too tight for the passenger to sit on.
The passenger seat was designed to be slightly wider than the first sample to allow room for a larger man to sit in the passenger seat.It is a tight fit without sacrificing passenger comfort.
■Maximum loading capacity is 5kg.World Walk is reinforcing every part of it.
Recently, it has become common to install a rear carrier and a rear box as a set, even for super sports inspired vehicles.Some of the larger rear boxes weigh about 5kg, so I reinforced each part of the box and set the maximum load capacity to 5kg.
The reinforcement plate is placed on the frame where the rear carrier is installed, and also on the legs of the main body.
■The shape of the buttocks is designed for practicality and design.
When the rear box is installed, the lid may close by itself if it is horizontal or raised forward when the lid is opened.This is why the rear rack is designed to be raised backwards.The angle of the tail cowl is the same as the angle of the tail cowl, so the design has a sense of unity.
To install, remove the grab bar from MT-25 / 03.YZF-R25 / 3 requires drilling of some parts of the tail cowl, but World Walk has designed the cowl so that drilling of the cowl is minimized.A paper pattern is also included to help you know where to drill the holes.